237-242
Research, Design, Calculations, and Operating Experience
Results of modernization of vacuum evaporator systems for production of wet-process phosphoric acid
V. G. Trukhan, P. M. Salikov and N. P. Kakurkin
243-248
Numerical investigation of stress concentration in a large-diameter threaded connection
T. A. Komarova, Yu. S. Kuz’min and V. G. Fedosov
249-252
Determination of mass-transfer surface for methylene chloride extraction of petroleum products from water
D. A. Ivanov and A. M. Volchek
253-258
Cryogenic Engineering, Production and Use of Industrial Gases, Refrigeration engineering
Current trends in the development of low-potential power engineering
I. M. Kalnin’
259-269
Development and creation of an efficient Khrom-3 unit for preparing krypton-xenon mixtures
M. Yu. Savinov, A. M. Arkharov, V. E. Poznyak and V. L. Bondarenko
270-274
Compressors, Pumps, and Pipeline Fittings
Analysis of gas motion in the clearance between the cover disk and the casing of centrifugal compressor stage
Yu. B. Galerkin and K. V. Soldatova
275-279
Nanotechnology in compressor and pump engineering
A. P. Morgunov, A. I. Blesman, V. S. Kalekin, A. M. Lasitsa and V. G. Churankin
280-286
Complementary Products and Devices
Function division in wear-resistant pipeline elements
I. N. Karelin
287-291
Industrial Ecology
Cleaning diesel plant exhaust gases
A. Yu. Val’dberg, T. O. Kosogorova, A. N. Tsedilin, D. D. Pokrovskii and A. A. Yakimychev
295-300
Research, Design, Calculations, and Operating Experience
Experimental-industrial reactor for synthesis of carbon nanostructural materials by chemical gas-phase deposition on a catalyst
A. G. Tkachev
301-306
Modeling the mixing of cohesionless materials when the flow of granular medium occurs with plastic shear deformations
V. N. Dolgunin, V. Ya. Borshchev and R. A. Shubin
307-311
Operating efficiency and hydrodynamics of conical dust collectors with swirling counterflows
I. A. Petrov, É. F. Shurgal’skii and I. V. Chepura
312-314
Granulation of diammonium phosphate in a drum granulator-drier
I. G. Grishaev and V. A. Grinevich
315-318
Hydrodynamics of eddy flow in a smooth-wall mixer-equipped vessel
L. A. Tarasova, S. V. Orlov and O. A. Troshkin
319-322
Mathematical modeling of control systems for production processes with distributed parameters
L. V. Kulagina
323-329
Cryogenic Engineering, Production and Use of Industrial Gases, Refrigeration Engineering
Natural gas liquifier based on an EGD-generator-expander
G. I. Bumagin, D. V. Borodin, A. G. Lapkova, A. E. Rakhanskii and E. I. Rogal’skii
330-334
Study of adsorption deposition of xenon in an industrial unit for processing ASU tail streams
A. M. Arkharov, M. Yu. Savinov, V. L. Bondarenko, M. Yu. Kolpakov and V. B. Vorotyntsev
335-342
Compressors, Pumps, and Pipeline Fittings
Selecting optimum density of lattice of blades of screw pump impeller
I. V. Shcherbatenko, E. P. Ivanova and V. I. Surikov
343-350
Similarity method for studying and calculating convective heat exchange in piston machines
V. S. Kalekin and D. V. Kalekin
351-354
Piston compressor parameter comparison for operation with air and freon
Yu. A. Antipov, M. V. Loban and A. A. Kiryushkin
355-357
Ways of reducing the irrecoverable losses of oil from compressor oiling systems in Ural-series gas pumping plant
S. I. Burdyugov, A. F. Grokhotov and A. O. Gabitov
358-361
Industrial Ecology
Air pollution near a port oil terminal
T. Lashkova, V. Zabukas, P. Baltrenas and P. Vaitiekunas
362-366
Effects of gas exit conditions from electrical filters on the dust trapping performance
Ya. L. Ginzburg and L. V. Chekalov
367-370
Materials Science and Corrosion Protection
Using gas ducts made of glass-reinforced plastic for drawing off sulfur dioxide
V. G. Makarov, R. M. Sinel’nikova and A. P. Aleksandrov